Whirlpool washing machine error codes - Sanitisation Singapore

Many appliances are used in homes on a daily or at least weekly basis and washing machines are one such product. Whirlpool is one of the top companies in the world that manufacture washing machines and they are being used around the world. The company makes products of high quality that rarely face any issues or difficulties in operating. However, just like any other products in the world, Whirlpool washing machines also malfunction or stop working sometimes.

The good thing is that an error code is displayed on the screen as an indication of the actual issue in the washing machine. For your convenience, we have gathered all the error codes that can occur in Whirlpool washing machines along with their causes and solutions. If you are unable to take down the error even after implementing the suggested solution, you should contact the Whirlpool customer support service for guidance and technical help at 1-866-698-2538.

Table of Contents

Whirlpool washing machine error code F01

Cause:

This error occurs when there are some issues with the main electrical circuit board of the washing machine.
Some or all of the machine’s functions are not selectable or operating.

Solution:

Unplug the switch from the socket and let the washing machine reset for about 2 minutes. Plug the switch again into the sockets and turn the washing machine ON after waiting for 30 seconds.
If you are still getting the error, seek help from a technician to check the wiring and connections of the circuit board. Repair or replace the circuit board if damaged.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F02

Cause:

This error is reported by Whirlpool washing machines when the main circuit board of the washer motor is at fault.
The washer tub is not spinning even when it is on a wash cycle.

Solution:

Turn OFF the washing machine for about 30-60 seconds and then turn it ON again. Run a new wash cycle.
If the error is still there, seek help from a technician to check the washer circuit board, its wiring and connections.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F03

Cause:

This error occurs when the temperature-detecting sensor is not working effectively or is completely faulty.
The washing machine is not heating up on both wash and dryer settings.

Solution:

Seek help from a technician to check the temperature-detecting sensor and if faulty, replace it.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F05

Cause:

This error can occur due to multiple issues in the water-draining mechanism of the washing machine.

The drain hose has kinks, leaks, clogs, or is completely damaged.
The filters in the drain pump are blocked mostly because of dirt and fiber scrap build-up.
The drain pump itself is faulty.

Solution:

Remove kinks and blockages from the drain hose. Repair leaks and if completely damaged, replace the hose.
Check the pump filter and remove dirt and debris from them.
Check the drain pump and if it is faulty, seek the help of a professional technician to check it and further guide you on what should be done.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F06, F5 E32, LdL

Cause:

This error occurs when the washing machine door is not closing.
There is something such as a cloth preventing the door from closing.
The door lock mechanism is faulty and needs replacement.

Solution:

Close the washer door if it was opened previously.
Replace anything coming between the door closing path such as laundry.
Clean the door latches and all moving parts using a cotton swab dipped in a cleaner or rubbing alcohol such as IPA.
If you are still getting the error, the door lock mechanism is at fault. Clean it or replace it if damaged.

Whirlpool washing machine error code F07, F08

Cause:

This error occurs due to multiple reasons such as:

The main electrical circuit board of the washer is malfunctioning. The wash cycle abruptly stops during the wash cycle.
The heating circuit of the washing machine is faulty.

Solution:

Turn OFF the washing machine for about 30 seconds and turn it ON again. Start a new cycle.
If still getting the error, call a professional technician to check the heating and electrical circuit board of the washing machine for any faults. Replace the boards if damaged.

Whirlpool washing machine error code F09

Cause:

This error is displayed on the washing machine screen when some software is not operating or is corrupted.
The washing machine is not functioning and you are unable to select a function or program.
Multiple lights are flashing or the display screen itself is flashing.

Solution:

It is recommended to call the customer support service of Whirlpool for guidance or the operator at 1-866-698-2538. They have full access to the software and know better about the programs in the washing machine.

Whirlpool washing machine error code F11

Cause:

This error is a clear indication that the drain pump circuit of the washer is at fault or completely damaged.
The water is being held in the drain pump instead of coming out.

Solution:

Open the drain pump to clean the filters and the pump itself.
Turn OFF the washing machine for about 30 seconds and turn it ON again.
If still getting the error, replace the drain pump or seek help from a professional operator by calling 1-866-698-2538.

Whirlpool washing machine error code F12

Cause:

This error occurs when there is some issue in the electronic control board that handles the overall functions and operations of the washing machine.
The washing machine is not turning ON.

Solution:

Seek the assistance of a professional technician to check the control board and related wiring and connections. Repair or replace parts as needed.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F13

Cause:

This error indicates some fault in the temperature-detecting sensor of the dryer.
The dryer of the washing machine is not working to dry the laundry.

Solution:

Check the wiring and connections between the temperature sensor and the main PCB. Make sure they are not loose or broken.
Check the temperature-detecting sensor for any faults. If defective, replace it.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F15

Cause:

This error occurs when there is some fault in the heater control of the washer and dryer.
The wash and drying cycle is stopping partway through the wash cycle without any reason.

Solution:

Seek help from an electrician to check the wiring, connections, and other electronics of the control board. Repair or replace elements as needed.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F16

Cause:

This error only occurs in the Whirlpool Top Loading washing machines.

It occurs when/if the washer tub is stopping at a working position instead of locking at its intended position.

Solution:

Check the drum lock position sensor for any faults. Replace the sensor if it is defective or damaged.
If you are still getting the error, seek help from a technician or call Whirlpool’s customer support for guidance at 1-866-698-2538.

Whirlpool washing machine error code F18

Cause:

This error occurs when there is some internal data or communication error in the washing machine.
Some or all of the functions, programs, buttons, or display options are not working.

Solution:

Unplug your washing machine and keep it turned OFF for about 2 minutes. Plug the switch again and press the power button after 30 seconds to see if everything comes to its normal functioning.
If still getting the error, call a local technician or whirlpool customer support at 1-866-698-2538.

Whirlpool washing machine error code F19

Cause:

This error occurs due to two main reasons.

The fan motor is spinning slowly or not at all. This can happen only in Whirlpool dryers.
The heating elements of the washing machine are at fault.
The dryer isn’t drying the laundry or it is stopping abruptly partway through the drying cycle.

Solution:

Check and make sure that proper voltages are being supplied to the fan motor and other components of the machine.
Check the heating components for any loose connections. Replace elements if needed.
If you are still getting the error, call the electrician to check the heating components and motors or call Whirlpool’s customer support for guidance at 1-866-698-2538.

Whirlpool washing machine error code LOC, LC

Cause:

This error is directly related to Control Lock and occurs when/if:

You mistakenly pressed the control lock button on the washing machine.

Solution:

For most models, there will be a touch button on the washing machine panel that can deactivate the Control Lock simply by pressing it again.
For some older models or mostly in Whirlpool Front Loading washing machines, there will be a manual button. Simply press and hold that button for 3-5 seconds and the control lock will be deactivated.
Restart the washing machine after turning it OFF for 30-60 seconds.

Whirlpool washing machine error code dET

Cause:

This error occurs only in a few models of Whirlpool washing machines and indicates that the detergent cartridge is not installed in the dispenser.

Solution:

Check the detergent cartridge and make sure that it is inserted in its intended position in the proper manner.
Open the washing machine drawer and shut the drawer again.
Ignore the error if you are only using single-load doses of detergent for your washing machine.

Whirlpool washing machine error code Int

Cause:

This error only occurs due to the user’s interruption in the wash cycle.

This error is triggered when a user abruptly pauses or cancels a particular wash cycle by himself/herself.

Solution:

Press the “Pause” or “Cancel” button again. The error will be taken down once the wash cycle starts spinning again.
If still getting the error, unplug the washing machine switch and then turn it ON again after waiting for about 1-2 minutes. Starts a new wash cycle.

It is recommended to call Whirlpool’s customer support for further guidance at 1-866-698-2538.

Whirlpool washing machine error code F34, rL

Cause:

This error only occurs when the washing machine is running a clean washer cycle and it detects some foreign objects in the washer tub.

Solution:

Pause the Clean Washer cycle and take the foreign objects out of the tub. Resume the wash cycle again.

Whirlpool washing machine error code SUD

Cause:

This error is reported by the Whirlpool washing machine when there are too many suds in the washer tub.

Solution:

Pause the wash cycle and remove excess amounts of suds from the washer tub.
Whirlpool washing machines themselves try to tackle this error by increasing the rinsing and pausing cycles. Doing so allows the bubbles to break down, decreasing the suds, and thus removing the error.
Make sure that you only use HE (High-Efficiency) laundry detergent in your washer.
Always use regular liquid bleach and make sure you never put liquid chlorine bleach as it has a thickening agent which can increase the probability of causing suds.
Check the drain hose and remove if there are any kinks or leaks. Replace the hose if damaged.

Whirlpool washing machine error code F7 E1

Cause:

The “F7 E1” error is displayed on the washing machine screen when/if the main motor is not reaching a specific speed required for running a particular wash cycle.

Solution:

Check and make sure that you have removed all the shipping bolts from the machine.
Make sure that the washer tub is not overloaded. Remove some laundry if required.
Once you remove the error, press the “Pause” or “Cancel” button on the panel or option twice on the touch screen and then the “Power” button once.

Whirlpool washing machine error code F8 E1, LO FL

Cause:

This error is reported by the washing machine and it detects a decrease in water flow into the washer drum.

Solution:

Check and make sure that the water supply tap and water inlet valves are fully turned ON and there is no clogging.
Make sure that the water inlet hoses have no kinks, bents, or leaks. Repair or replace the water supply hoses as required.
Remove the anti-flood controls or features as they sometimes stop the water supply assuming there’s a leak.

Whirlpool washing machine error code F8 E2

Cause:

This error indicates that the dispenser system of the washing machine has some issues.

Solution:

Open the detergent drawer and make sure that nothing is causing a clog in the detergent supply path.
Clean the drawer nozzle and shut it properly.
Make sure that the detergent cartridge is installed in its intended position.

Whirlpool washing machine error code F9 E1

Cause:

This error occurs when drain pumps take longer than the normal limit of 8 minutes, to drain the water out of the washer drum.

Solution:

Check the drain hoses for any kinks, leaks, bents, or something causing a blockage. Clean and repair the hose.
If suds are the reason behind this error, just wait and the error will be down once the water is fully drained out.

Whirlpool washing machine error code F# E#, F##

Cause:

This is known as a miscellaneous error as it can happen due to any minor technical issues in the washing machine.

Solution:

Unplug the washing machine for 1-2 minutes and then turn it ON again. Restart the new cycle
If you are still getting the error, call a local technician or customer support for assistance at 1-866-698-2538.

Whirlpool washing machine error code dm

Cause:

This error is a clear indication the drain hose is not installed in its intended position.

Solution:

Check the drain hose and install at the right location and place it in the right position. Seek assistance from a technician if required.

Whirlpool washing machine error code HC

Cause:

This error will only occur at the end of a washing cycle when/if:

Either the hot or cold water inlet valves of the washing machine are not installed correctly.

Solution:

Turn OFF the water supply into the washer and reverse the hot and cold inlet hoses.
Check and make sure that cold and hot inlet water hoses are installed correctly in their intended locations.

Whirlpool washing machine error code LdU

Cause:

This error occurs only when/if the washing machine is unable to unlock the washer door.

Solution:

The door will unlock automatically as soon as you do the following things.

Remove the objects if they are placed on the washing machine lid.
Remove the items that are placed in front of the washer door such as laundry or a bucket.

Whirlpool washing machine error code F8 E1, LF, LoFL

Cause:

This error is reported by Whirlpool washing machines when water is taking too long (more than 8 minutes) to fill the washer drum.

Solution:

Check and make sure that the water supply taps are fully turned ON.
Look through the water supply hoses for any kinks, leaks, bends, or blockages. Clean, repair, or replace the water supply hoses as required.
Make sure that water inlet valves are open and that no dirt, detergent, or fiber scrap build-up is causing blockages.
Increase the water pressure of the washing machine as the water pressure can also trigger this error.

Whirlpool washing machine error code lid

Cause:

This error occurs only when/if the door or lid of the washing machine was left open longer than a normal period of 10 minutes.

Doing so will cause the washing machine to cancel or reset the wash cycle that was set and will drain all the water out of the washer.

Solution:

Close the lid and start a new wash cycle.

You may not add more detergent to the washing machine as the laundry will have the previously added detergent absorbed in it.

Whirlpool washing machine error code Ofb

Cause:

This error is reported by the Whirlpool washing machine when it is not balanced. This can happen because of issues like:

The laundry inside the washer has rolled into a ball and is now sitting on one side of the washing machine.
There is too much water inside the washer drum of the washing machine.
The washer drum has stopped spinning or its speed is reduced to a greater extent.

Solution:

Pause the wash cycle and take out laundry from the washer. Separate clothes and distribute them evenly into the washing machine. Resume the wash cycle.
Drain some water out of the washing machine.
Add some more laundry into the washer if previously, there was too little.
Make sure that the washing machine is placed on an even and leveled surface.
Turn OFF the washing machine for about 30-60 seconds and then turn it ON again.

Whirlpool washing machine error code OL

Cause:

The OL stands for Overload and this error occurs when/if there is too much laundry in the washing machine.
There is a heavy piece of laundry such as a blanket, which has rolled into a ball and is now sitting still in the washer tub.

Solution:

Remove some clothes if there is too much laundry in the washing machine.
Take out the rolled garment, make it lose, and put it back into the washing machine.
Drain some water out of the washing machine.
Make sure you are using HE detergent to prevent too many suds in the washer.

Whirlpool washing machine error code PF

Cause:

This error occurs when there was a complete power failure or an abrupt interruption that disturbed the normal function of the washing machine.

Solution:

Most models of Whirlpool washing machines restart automatically once the power failure is removed and complete voltages are being supplied to the motor. If your model doesn’t start automatically: